OUTPUT

Configure the output settings for copies using Sort, Group, Offset, Separator Page, Staple, Punch, or Fold. Also specify the output destination of copies.
You can tap the [Output] key in normal mode to configure settings for all output functions.
Settings for the staple and punch functions can also be configured from simple mode.

Output Tray
Specify the destination to output copies.
If a finisher (large stacker) or saddle stitch finisher (large stacker) is installed, you can select [Upper Tray], [Middle Tray], or [Lower Tray].
Offset
This function outputs copies while shifting them set by set. Setting the checkbox to

enables the offset function, and setting it to

disables the function.

This function is available when a finisher or saddle stitch finisher is installed and [Upper Tray], [Lower Tray] or [Finisher Tray] is selected as the output tray.

Selecting the staple function clears the Offset checkmark automatically.

Separator Page
This function inserts separator pages for every specified number of copies or for every job before they are output.
REPEATING THE SAME IMAGE ON ONE SHEET (REPEAT LAYOUT)
Sort/Group
Select the sorting method when copying the scanned original.
"Sort" sorts the scanned original on a set basis, and outputs them. "Group" sorts the scanned original on a page basis, and outputs them.
SORT/GROUP SETTING
Staple
Each set of copies can be stapled, or the sheets can be folded at the centre and stapled.
Staple ON (excluding saddle stitch)
Saddle Stitch

The staple function is available only when the finisher or saddle stitch finisher is installed.
The saddle stitch function is available only when the saddle stitch finisher is installed.

Punch
This function punches copies and outputs them.
PUNCH SETTINGS

The punch function is available only when the punch module is installed.

Fold
Copies can be folded and output.
FOLD SETTING

The folding function is available when a finisher or saddle finisher is installed and [Upper Tray], [Lower Tray] or [Finisher Tray] is selected as the paper output destination.

CHANGING OUTPUT DESTINATION

Specify the destination to output copies.

Tap the [Detail] key to change to normal mode.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Select the output tray from "Output Tray".

After the settings are completed, tap [OK] key.

If a finisher (large stacker) or saddle stitch finisher (large stacker) is installed, select the [Upper Tray], [Middle Tray] or [Lower Tray] key.

SORT/GROUP SETTING

This section explains how to select the sorting method when outputting the scanned original.

Auto	Enables the sort mode when the original is placed in the automatic document feeder, and enables the group mode when the original is placed on the document glass.
Sort	Sorts the scanned original on a set basis, and outputs them. Example: When 5 is set for the number of copies in sorting
Group	Groups the scanned original on a page basis, and outputs them. Example: When 5 is set for the number of copies in grouping

Auto

Enables the sort mode when the original is placed in the automatic document feeder, and enables the group mode when the original is placed on the document glass.

Sort

Sorts the scanned original on a set basis, and outputs them.

Example: When 5 is set for the number of copies in sorting

Group

Groups the scanned original on a page basis, and outputs them.

Example: When 5 is set for the number of copies in grouping

Tap the [Detail] key to change to normal mode.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Tap the [Sort/Group] tab, then tap the [Auto] key, the [Sort] key, or the [Group] key.

After the settings are completed, tap [OK] key.

You can select the offset output checkbox to have each set of output be offset from the previous set to enable easy removal from the output tray.
To change the output tray, tap the [Output Tray] key, and select the output destination.

STAPLE SETTINGS

Specify whether or not the set of output will be stapled.
Portrait orientation

Original Orientation	Staple	Staple Position
Original Orientation	Staple	Left	Top	Right
Portrait orientation	1 Staples
Portrait orientation	2 Staples
Landscape orientation	1 Staples
Landscape orientation	2 Staples

You can view staple positions on the " PREVIEW SCREEN". Text will be printed at the preset size regardless of the copy ratio or paper size setting.
A finisher or saddle stitch finisher is required to use the staple function.
A finisher or saddle stitch finisher is required to use the staple function.u8226• A saddle stitch finisher is required to use the saddle stitch function.

Staple ON (excluding saddle stitch)

Tap the [Staple / Punch] key.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Select the number of staples and staple position.

After the settings are completed, tap [OK] key.

In normal mode

Tap the [Output] key and [Staple] tab.

To change the output paper output tray, select the output destination in [Output Tray] of [Other functions] before setting the staples.
If the number of scanned originals exceeds the staple sheet limit, a message is displayed. Tap [Continue] or [Cancel].

Saddle Stitch

Tap the [Staple / Punch] key.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Select .

Select binding edge and original settings.

MAKING COPIES IN PAMPHLET FORMAT (BOOKLET)
After the settings are completed, tap [OK] key.

Staple settings in normal mode

Tap the [Detail] key to change to normal mode.

EASY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Tap the [Staple] tab, and tap the staple position key.

Staple position can be selected from "Position" when selecting keys other than [Off], [1 Staple (Diagonal)], and [Saddle Stitch].
After the settings are completed, tap [OK] key.

If you perform 1-staple stapling with a finisher or saddle stitch finisher installed, all staples will be stapled diagonally.
If the number of scanned originals exceeds the staple sheet limit, a message is displayed. Tap the [Continue] or [Cancel] key.

To cancel the staple function:
Tap the [Off] key.

Saddle stitching for sorted copies

This function staples each set of copies at two positions in the centre of paper, folds them in half, and outputs them. For saddle folding, it trims a side drop, offering a good-looking output image. The setting procedure in normal mode is explained.

You can view staple positions in " PREVIEW SCREEN".
A saddle stitch finisher is required to use the saddle stitch function.
The trimmer function is available when a trimmer unit is installed on the machine.

Saddle Stitch (Normal mode)

Tap the [Detail] key to change to normal mode.

EASY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Tap the [Staple] tab, and tap the [Saddle Stitch] key.

Tap the [Left Binding/Tablet] or [Right Binding] key to select an original and configure the cover sheet setting.

After the settings are completed, tap [OK] key.

The original will be scanned from the innermost side when folded.
If the number of scanned originals exceeds the staple sheet limit, a message is displayed. Tap [Divide], [Continue] or [Cancel].

To cancel the Saddle Stitch:
Tap the [Off] key.

Trimmer Setting

When Saddle Stitch is selected, tap the [Trimmer Setting] key.

Tap the [On] key, and specify the trimming width.

Tap the numeric value display field of the trimming width, and enter the allowable range using the numeric keys. Otherwise, tap

. After the settings are completed, tap [OK] key.

To cancel the Trimmer Setting:
Tap the [Off] key.

PUNCH SETTINGS

This function punches copies and outputs them to the tray.
Example: When the original is in either portrait or landscape orientation, and the punch position is set to the left

Original Orientation	Punch Position
Original Orientation	Left	Top	Right
OFF	Does not punch.
Portrait orientation
Landscape orientation

When staple and punch are set at the same time, punch positions are linked to staple positions.
You can view punch positions on the " PREVIEW SCREEN".
A punch module is required for paper punch.
You cannot use 12" x 18" (A3W) size paper or special media such as transparency film and tab paper.
You cannot use a paper punch together with the staple and paper folding.

Tap the [Staple / Punch] key.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Select punching and set the position.

After the settings are completed, tap [OK].

Normal mode

Tap the [Detail] key to change to normal mode.

EASY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Tap the [Punch] tab, select punching and set the position.

To change the output tray, tap the [Output Tray] key, and select the output destination.
After the settings are completed, tap [OK] key.

To cancel the punch Setting:
Tap the [Off] key.

FOLD SETTING

This function is used to fold copies before delivery to the output tray.
When a paper folding unit is installed, you can fold papers in Z-fold and C-fold.
When a saddle stitch finisher is installed, you can use saddle folds.
The paper sizes that can be selected vary depending on the type of paper fold.
Example: Fold Inside, Fold Outside

A saddle stitch finisher is required to use Saddle Fold.
The paper folding function cannot be used with the staple and hole punch function. However, it can be used with them if the paper size for Z-folding is set to 11" × 17", A3, or B4.
You can check the selected folding method in " PREVIEW SCREEN".
A folding unit is required to use Half Fold, C-Fold, Accordion Fold, Double Fold, and Z-Fold.
If a paper size that cannot be folding is selected and folding is executed, folding will not be executed and only copying will be executed.

Types of folds and paper sizes available

Folding types	Usable paper	Print Side	Fold Orientation
Saddle Fold	Saddle stitch finisher (large stacker): A3W, A3, B4, A4R, SRA3, 13" × 19", 12" × 18", 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11"R, 8K	Inside	-
Saddle Fold		Outside	-
Half Fold	A4R, 8-1/2" × 11"R	Inside	-
Half Fold	A4R, 8-1/2" × 11"R	Outside	-
C-Fold	A4R, 8-1/2" × 11"R	Inside	Open Right
		Inside	Open Left
		Outside	Open Right
		Outside	Open Left
Accordion Fold	A4R, 8-1/2" × 11"R	-	Open Right
Accordion Fold	A4R, 8-1/2" × 11"R	-	Open Left
Double Fold	A4R, 8-1/2" × 11"R	Inside	Open Right
		Inside	Open Left
		Outside	Open Right
		Outside	Open Left
Z-Fold	A3, B4, A4R, 11" × 17", 8-1/2" × 14", 8-1/2" × 11"R,	-	Open Right
Z-Fold	A3, B4, A4R, 11" × 17", 8-1/2" × 14", 8-1/2" × 11"R,	-	Open Left

Tap the [Detail] key to change to normal mode.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Tap the [Fold] tab, and tap the folding type key.

To cancel the paper folding function:
Tap the [Off] key.

Tap the [Detail] key.

For the setting method, see " Detail Type for each Folding Type".
After the settings are completed, tap the [OK] key.

Detail Type for each Folding Type

Saddle Fold

Specify "Print Side" and "Multiple Fold".

The Multiple Fold function folds five sheets at a time. For example, if an original has 12 A4 size plain sheets, they are folded three times in total: 5 sheets + 5 sheets + 2 sheets. However, some types of paper reduces the number of sheets that are folded every set. For example, heavy paper is folded on a three-sheet basis.

Half Fold

Specify "Print Side".

C-Fold

Specify "Print Side" and "Fold Orientation".

Accordion Fold

Specify "Fold Orientation".

Double Fold

Specify "Print Side" and "Fold Orientation".

Z-Fold

Specify the paper size and "Fold Orientation" for Z-folding.

INSERTING SEPARATOR PAGES BETWEEN COPIES OR JOBS

This function inserts separator pages between each set of copies or between each job.
When you insert separator pages between sets of copies, you can specify whether to insert the separator page before or after each set. You can also specify the number of copies that makes one set.
When you insert separator pages between jobs, you can specify whether to insert a separator page before or after each job.

Separator page insertion examples

In the following examples, four copies of a two-page original are output.
Inserting a separator page before each set of two copies

Inserting a separator page after each set of two copies

Inserting separator pages before and after a job

When this function is combined with Sort/Group and Staple/Punch, Z-fold and half fold are not applied to the separator pages.
This function cannot be used with the saddle stitch or fold function.
This function cannot be used in combination with staple/punch and insertion of divider for each job.
When used in combination with the offset function, a separator page is never offset by itself; the separator page is always offset together with the set of output.

Tap the [Detail] key to change to normal mode.

COPY MODE

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Tap the [Output] key.

Tap the [Separator Page] key.

Specify the separator page insertion mode.

To insert separator pages between sets of copies, set the [Insert Top of Sets] or [Insert End of Sets] checkbox to . Next, tap to specify the number of copies in each set.
To insert separator pages between jobs, set the [Insert Before Job] or [Insert After Job] checkbox to .
After the settings are completed, tap [OK] key.

To change the separator page tray:
Tap the [Paper Tray] key to display the tray selection screen. Tap the separator page tray in the tray selection screen. For more information, see " SELECTING THE PAPER TRAY FOR COPYING" and " SPECIFYING A TYPE AND SIZE OF PAPER LOADED ON BYPASS TRAY".

To cancel the separator page insertion setting:
Clear the checkmark for separator page insertion mode.

OUTPUT

CHANGING OUTPUT DESTINATION

SORT/GROUP SETTING

STAPLE SETTINGS

Staple ON (excluding saddle stitch)

Saddle Stitch

Staple settings in normal mode

Saddle stitching for sorted copies

Saddle Stitch (Normal mode)

Trimmer Setting

PUNCH SETTINGS

Normal mode

FOLD SETTING

Types of folds and paper sizes available

Detail Type for each Folding Type

Saddle Fold

Half Fold

C-Fold

Accordion Fold

Double Fold

Z-Fold

INSERTING SEPARATOR PAGES BETWEEN COPIES OR JOBS

Separator page insertion examples

CONTENTS MENU