Paper Settings

Paper Tray Settings

Paper tray and paper type settings are explained in this section.
These settings specify the paper type, paper size, and functions allowed for each paper tray.
When the [Paper Tray Settings] key is tapped, a list appears showing the trays and the current settings.

Auto Switching of Tray

When a tray runs out of paper during printing, this determines whether or not another tray with the same size and type of paper is automatically selected and printing continues.

Factory default settings:: Disable

Display Paper Tray Settings when bypass tray detects paper.

You can have the paper tray settings appear automatically when paper is detected in the bypass tray.

Factory default settings:: Disable

Paper Weight Setting

These are used to control the toner fusing temperature according to the weight of the paper.
These settings apply to recycled paper, punched paper, pre-printed paper, letterhead paper, coloured paper, and user type paper. Enter "/".
You can select "60g/m² to 89g/m ²" or "90g/m² to 105g/m²" ("16 to 24 lbs." or "24+ to 28 lbs.").

Factory default settings:: 60 to 89g/m² (16 to 24 lbs.)

Settings of each tray

When the [Change] key is tapped, the corresponding setting screen appears.
The following settings can be configured.

List name	Description
Type	Select a type of paper to be loaded into the tray. The paper types that can be selected vary by paper tray. For more information see " Tray Settings". To user type setup, see " Paper Type Registration".
Size	Select the paper size from the list. The paper sizes that can be selected vary by tray. The sizes that can be selected may also be restricted by the paper type selected above. For more information see " Tray Settings". If the desired size does not appear in the list, select [Custom Size] and directly enter the size (only for the bypass tray). For more information see " Tray Settings".
Feeding Approved Job	Select the modes that can be used. If there is a function that you do not wish to be used with the selected tray, disable the function.

If the paper size specified here is different from the size of paper that is loaded into a tray, a problem or misfeed may occur when printing.
To change the paper size in a tray, see " IMPORTANT POINTS ABOUT PAPER".
Paper properties such as "Fixed Paper Side" are automatically set when the paper type is selected. The paper tray properties cannot be changed in this screen.
[Settings] → [System Settings] → [Common Settings] → [Device Control] → [Default Settings] → [Disabling of Tray Settings], [Disabling of Large Capacity Cassette]. When it is set, the paper feed tray (excluding the bypass tray) cannot be set.

Tray Settings

Paper Tray	Paper Type	Size
Tray 1	Plain Paper 1 to 2*1, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, User Type	A4, B5, 8-1/2" x 11"
Tray 2	Plain Paper 1 to 2*1, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, User Type	A4, 8-1/2" x 11"
Tray 3	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Heavy Paper 1 to 42, User Type	Auto-AB (A3W, A3, B4, A4, A4R, B5, B5R, 216 x 330 mm (8-1/2" x 13")3), Auto-Inch (12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R), A4W (9" x 12"), 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")*3), 8K, 16K, 16KR
Tray 4	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Heavy Paper 1 to 42, Embossed, Envelope, Tab Paper, Transparencies, Labels, User Type	Auto-AB (A3W, A3, B4, A4, A4R, B5, B5R, A5R, 216 x 330 mm (8-1/2" x 13")3), Auto-Inch (12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R), A4W (9" x 12"), 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")*3), 8K, 16K, 16KR, custom size Monarch, COM9, COM10
Tray 5 (when a large capacity tray (MX-LC12) is installed)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Heavy Paper 1 to 22, User Type	A4, B5, 8-1/2" x 11"
Tray 5 (when a large capacity tray (MX-LCX3 N) is installed)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Heavy Paper 1 to 22, User Type	SRA3, SRA4, A3, B4, A4, A4R, B5, A3W (12" x 18"), 11"×17", 8-1/2" x 14", 216 x 330 mm (8-1/2" x 13"), 8-1/2" x 11", 8-1/2" x 11"R
Tray 5/7 (when a large capacity trays are installed)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Thin Paper, Heavy Paper 1 to 42, Heavy Paper (301 g/m² to 360 g/m² (110 lbs cover to 130 lbs cover)), Embossed, Tab Paper, Transparencies, Labels, Glossy Paper, User Type	Auto-AB (SRA3, A3W, A3, B4, SRA4, A4W, A4, A4R, B5, B5R, 13" x 19", 12" x 18", 11" x 17", 216 x 343 mm (8-1/2" x 13-1/2") 3, 216 x 340 mm (8-1/2" x 13-2/5") 3, 216 x 330 mm (8-1/2" x 13") 3, 8-1/2" x 11"), Auto-Inch (13" x 19", 12" x 18", 9" x 12", 11" x 17", 8-1/2" x 14"3, 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, SRA3, A3W, A3, B4, SRA4, A4W, A4, B5), 8K, 16K, 16KR, custom size
Tray 6/8 (when a large capacity trays are installed)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Thin Paper, Heavy Paper 1 to 42, Heavy Paper (301 g/m² to 360 g/m² (110 lbs cover to 130 lbs cover)), Embossed, Tab Paper, Transparencies, Labels, Glossy Paper, User Type	Auto-AB (SRA3, A3W, A3, B4, SRA4, A4W, A4, A4R, B5, B5R, 13" x 19", 12" x 18", 11" x 17", 216 x 343 mm (8-1/2" x 13-1/2") 3, 216 x 340 mm (8-1/2" x 13-2/5") 3, 216 x 330 mm (8-1/2" x 13") 3, 8-1/2" x 11"), Auto-Inch (13" x 19", 12" x 18", 9" x 12", 11" x 17", 8-1/2" x 14"3, 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, SRA3, A3W, A3, B4, SRA4, A4W, A4, B5), 8K, 16K, 16KR, custom size
Bypass tray (on the machine)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Thin Paper, Heavy Paper 1 to 42, Heavy Paper (301 g/m² to 360 g/m² (110 lbs cover to 130 lbs cover)), Embossed, Envelope, Tab Paper, Transparencies, Labels, Glossy Paper, User Type	Auto-AB (SRA3, A3W, A3, B4, SRA4, A4, A4R 3, B5, B5R, A5R, A6R, 13" x 19", 11" x 17", 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 216 x 330 mm (8-1/2" x 13"), 8-1/2" x 11"), Auto-Inch (13" x 19", 12" x 18", 11" x 17", 8-1/2" x 14"3, 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R *3, SRA3, A3, B4, SRA4, A4, B5), Monarch, COM9, COM10, DL, C4, C5, C6, A4W (9" x 12"), 8K, 16K, 16KR, custom size
Bypass tray (on the large capacity trays)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Thin Paper, Heavy Paper 1 to 22, Tab Paper, Transparencies, User Type	Auto-AB (A3W, A3, B4, A4W, A4, A4R 3, B5, B5R, A5R, 11" x 17", 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 216 x 330 mm (8-1/2" x 13")3, 8-1/2" x 11"), Auto-Inch (12" x 18", 11" x 17", 9" x 12", 8-1/2" x 14"3, 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 8-1/2" x 11", 8-1/2" x 11"R3, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, A3, B4, A4), 13" x 19", SRA3, SRA4, 8K, 16K, 16KR, custom size
Inserter (Upper tray)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Heavy Paper 1 to 22, User Type	Auto-AB (A3W, A3, B4, A4W, A4, A4R 3, B5, B5R, A5R, 11" x 17", 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 216 x 330 mm (8-1/2" x 13")3, 8-1/2" x 11"), Auto-Inch (12" x 18", 9" x 12", 11" x 17", 8-1/2" x 14"3, 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 8-1/2" x 11", 8-1/2" x 11"R3, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, A3, B4, A4W, A4), 13" x 19", SRA3, SRA4, 8K, 16K, 16KR, custom size
Inserter (Lower tray)	Plain Paper 1 to 21, Recycled, Colour, Letter Head, Pre-Printed, Pre-Punched, Heavy Paper 1 to 22, User Type	Auto-AB (A3W, A3, B4, A4W, A4, A4R 3, B5, B5R, A5R, 11" x 17", 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 216 x 330 mm (8-1/2" x 13")3, 8-1/2" x 11"), Auto-Inch (12" x 18", 9" x 12", 11" x 17", 8-1/2" x 14"3, 216 x 343 mm (8-1/2" x 13-1/2")3, 216 x 340 mm (8-1/2" x 13-2/5")3, 8-1/2" x 11", 8-1/2" x 11"R3, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, A3, B4, A4W, A4), 13" x 19", SRA3, SRA4, 8K, 16K, 16KR, custom size

Tray Registration

Select Paper Sizes for Auto Detection

"Select Paper Sizes for Auto Detection" in the bypass tray settings screen is used to select the paper size that is automatically detected from similar sizes when the automatic paper size detection takes place.
When paper that is the same size as one of the paper sizes in the settings is placed in the bypass tray, the size that is selected in the settings will be automatically detected.

List name	Description
Auto-AB	A4R, A5, 216mm x 330mm (8-1/2” x 13"), 216mm x 340mm (8-1/2" x 13-2/5"), 216mm x 343mm (8-1/2" x 13-1/2")
Auto-Inch	8-1/2" x 14", 8-1/2" x 13-2/5" (216 mm x 340 mm), 8-1/2" x 13-1/2" (216 mm x 343 mm)

Custom Size Registration (Bypass)

If you frequently use a non-standard size paper in the bypass tray, register that paper size in advance.
Registering the paper size saves you the trouble of setting the size each time you need to use it.
Up to Seven paper sizes can be registered.
Tap the key ([Custom 1] to [Custom 7]) in which you wish to register or change a paper size, and the registration screen appears.
Select whether you wish to enter the size in mm ("Size Input-AB") or inches ("Size Input-Inch"), and then set the X and Y dimensions of the paper.
"Size Input-AB"
The X direction can be set between 140mm and 457mm.
The Y direction can be set between 90mm and 320mm.

Factory default settings:: X: 420 mm, Y:297 mm

"Size Input-Inch"
The X direction can be set between 5-1/2" and 18".
The Y direction can be set between 3-5/8" and 12-1/2".

Factory default settings:: X: 17" Y: 11"

Paper Settings

When [Add] is tapped in Paper Settings selection in the paper tray settings, the Paper Settings registration screen appears. By selecting advanced settings in Paper Properties for the paper to be used, you can print using the most suitable conditions for the printed mater.
A maximum of 1000 properties can be registered.

The Paper Settings can also be set from Tray Settings/Paper Settings in the Home screen. Select User Type for the paper type selection, and tap "Add/Edit Paper Settings" in the action panel.

Item		Description
Name		Enter a name for the Paper Settings (maximum of 50 half or full width characters).
Search Number		Set a search number.
[Default Settings] tab
Paper Weight Setting		Set the paper weight to be used.
	Unit	Set the units used for the Paper Weight.
Paper Type		Set the paper type. Select the paper type based on the surface finish of the paper or select the envelope. The following types can be selected. Uncoated Paper Coated Paper (Gloss) Coated Paper (Matte) Embossed Envelope
Paper Information		Set when Colour paper, Tab Paper, or Pre-Punched paper is used.
Paper Property		Set the properties of the paper to be used. For the properties, refer to the settings in “Paper Type Registration”.
[Detail] tab
Fusing Temperature Settings		Set the appropriate fusing unit temperature for the paper to be used.
Fuser Pressure Setting		Adjust the pressure on the paper. Some types of paper such as thick paper may not bend easily, and this may cause transfer deviations. You can use this setting to adjust the pressure on the paper and reduce transfer deviations.
Double Feed Detection Setting		Specify whether double feeds are detected. This function cannot be used when paper heavier than 68 lbs. (256 g/m ²) is used.
Primary Transfer Setting		Set the current of the primary transfer unit that is used to transfer toner to the transfer belt. By adjusting the current of the primary transfer unit, transfer problems such as insufficient transfer to the transfer belt can be improved. Select settings for both black & white and 4 colour (black, cyan, magenta, yellow).
Secondary Transfer Setting		Set the current of the secondary transfer unit that is used to transfer toner from the transfer belt to the paper. By adjusting the current of the secondary transfer unit, transfer problems such as insufficient transfer to the paper can be improved. When Uncoated Paper is selected for [Paper Type] Set for the Side 1 and Side 2 for both black & white and colour. When other than Uncoated Paper is selected for [Paper Type] Select settings for both black & white and colour.
PTC Current Value Setting		Set the PTC discharge current. The PTC discharge current can be adjusted to obtain transferability suitable for the paper being used. When Embossed is selected for the [Paper Type] Set for both black & white and colour. When other than Embossed is selected for [Paper Type] Set for black & white and colour at the same time.
Transfer Condition Adjustment Setting		Set enable/disable of transfer environment correction of Primary Transfer Current Value, Secondary Transfer Current Value and PTC Current Value.
Motor Speed Setting		You can adjust the motor speed and the speed change timing.
Colour Reg. Adjustment		This performs colour registration adjustment.
Paper Reg. Adjustment		You need to bend the paper to print at the correct position on the paper. This function adjusts the proper amount of deflection.
Maximum Density Setting		This performs the adjustment of maximum density for each of Y/M/C/K.
Side 1/2, XY Ratio/Print Position Auto Adjust		By reading a chart (output paper) for adjustment, the XY ratio and XY print position on the Side 1/2 of the paper are automatically adjusted.
Side 1/2, XY Ratio Settings		Configure settings to equalize the size of the image in duplex printing. This adjusts the size of the image on the Side 1 and Side 2 sides of the paper.
Side 1/2, XY Print Position		Configure settings to make the Side 1 and Side 2 centres match in duplex printing. This corrects Side 1 and Side 2 misalignment.
Print Void Settings		Adjust void areas at the top, bottom, and front/rear direction (leading and trailing ends) of the paper.

Depending on the tray being used, there may be restrictions on the setting options that can be selected, or a setting may not be possible.
The parameters that can be set vary depending on the peripheral devices that are installed.
The Side 1/2, XY Ratio Settings can only be selected when the machine is used as a printer.
The characteristics of some paper types may not provide a suitable printing result.
When "Envelope" is selected for the paper type, the below settings are fixed and cannot be changed.

Paper Weight Setting
Paper Information
Paper Property
Fuser Pressure Setting
Double Feed Detection Setting
Motor Speed Setting
Side 1/2, XY Ratio Settings
Side 1/2, XY Print Position

Side 1/2, XY Ratio/Print Position Auto Adjust

By reading a chart (output paper) for adjustment, the XY ratio and XY print position on the Side 1/2 of the paper are automatically adjusted.

When using this function, register the Paper Settings in advance.

For automatic document feeder

Tap [Document Feeder].

Print and read the chart.

Select the number of charts and tap [Print Chart].
Place the chart side 1 into the automatic document feeder and tap [Read].
Place the chart side 2 into the automatic document feeder and tap [Read].

When the adjustment result is displayed, tap [Register].

Tap [Cancel] to return to the Detail Settings screen without registering the settings.

For document glass

Tap [Document Glass].

Tap [Print Auto-adjustment Cover Sheet], print the cover sheet, then select the number of charts, and tap [Print Chart].

When the cover sheet remains from a previous automatic adjustment of the document glass, it is not necessary to print the cover sheet.

Print and read the chart.

Place the chart side 1 on the document glass, place the printed side of the cover sheet on the document glass, overlap the cover sheet so that the left and top edges of the chart are covered, and tap [Read].
Rotate the chart side 1 180 degrees, place it on the document glass, place the printed side of the cover sheet on the document glass, overlap the cover sheet so that the left and top edges of the chart are covered, and tap [Read].
Place the chart side 2 on the document glass, place the printed side of the cover sheet on the document glass, overlap the cover sheet so that the left and top edges of the chart are covered, and tap [Read].
Rotate the chart side 2 180 degrees, place it on the document glass, place the printed side of the cover sheet on the document glass, overlap the cover sheet so that the left and top edges of the chart are covered, and tap [Read].
To load the next chart, tap [Read Next Chart], and to exit, tap [Read-End].

When the adjustment result is displayed, tap [Register].

Tap [Cancel] to return to the Detail Settings screen without registering the settings.

Side 1/2, XY Ratio Settings / Side 1/2, XY Print Position

Side 1/2, XY Ratio Settings

The Side 1/2, XY Ratio Settings are used to eliminate print deviation by changing the Side 1/Side 2 ratio so that the print sizes match.
Tap [Change] in the Side 1/2, XY Ratio Settings to display the advanced settings screen of the Side 1/2, XY Ratio Settings.

Print a test pattern

Calculate the values from the pattern and enter the values.

[AB sizes]

[Inch sizes]

Measurement Line (Measurement Marker)	Length specified by measurement line interval
Assistant Line	50 mm (1.969 inch)
	100 mm
	5 inch

Tap [OK].
Return to step 1 and check the result of adjustment.

If the print position has shifted due to these settings, configure the Side 1/2, XY Print Position Settings.
The Side 1/2, XY Ratio Settings can only be used when the machine is used as a printer.

Side 1/2, XY Print Position Settings

The Side 1/2, XY Print Position Settings are used to make the centres of the Side 1 and Side 2 print positions match to remove printing misalignment.
Tap the [Change] button in Side 1/2, XY Print Position Settings to display the advanced settings screen of Side 1/2, XY Print Position Settings.

Select the units used in the Side 1/2, XY Print Position Settings

Print a test pattern

Measurement patterns for Side 1/2, XY Ratio Settings / Side 1/2, XY Print Position Settings

Read the scale from the patterns and enter the values.

Tap [OK].
Return to step 2 and check the result of adjustment.

The measurement line content of the measurement pattern varies depending on the paper size. Measure from the measurement line closest to the edge of the paper.
It may not be possible to guarantee the operation adjustment range in the Y direction of (± 3 mm) depending on the machine settings or paper size.
When the vertical or horizontal width is 100 mm or less, measure from the assistant line.
If you need to use this setting together with the Side 1/2, XY Ratio Settings, specify the Side 1/2, XY Ratio Settings first.
Changes in the environment of the machine, such as humidity and temperature, may cause a deviation of about 1 mm in the Side 1/2, XY Print Position.

Measurement patterns for Side 1/2, XY Ratio Settings / Side 1/2, XY Print Position Settings

To specify Side 1/2, XY Print Position Settings and Side 1/2, XY Ratio Settings, print a pattern for measurement.
Content of the measurement pattern

No.	Item	Description
1	Measurement Line	Reference line for measurement. Measurement lines for AB sizes and inch sizes have been created.
2	Dot Line	This line is visible through the Side 1 and Side 2 to let you visually check for misalignment. The line is printed at the same position on the Side 1 and Side 2. If visual inspection reveals that the lines are not aligned, the print positions on the Side 1 and Side 2 are not aligned.
3	Assistant Line	Assistant line located 25 mm from the centre of the paper. When the paper size is 100 mm or less, use this line for measurement.
4	Notes (Side 1/Side 2)	These indicate the Side 1 and Side 2.
5	Notes (X/Y axis)	When entering the settings, these indicate the X and Y axes of the paper.
6	Assistant Line (Magnification)	Indicates a position that is ±1% of the measured distance.

The same measurement pattern content is printed at the same size, regardless of the paper size. The outer perimeter of the measurement pattern is trimmed to match the paper size.
Example: Content trimmed for an AB size

Example: Content trimmed for an inch size

Paper Type Registration

Store a paper type when the desired paper type does not appear as a selection or when you wish to create a new set of paper properties.
Up to 11 paper types can be registered.

List name	Description
Type Name	Register any name. The factory default names are "User Type 1" to "User Type 11".
Fixed Paper Side	Use this setting when paper with a front and reverse side is used. Factory default settings: Disable
Disable Duplex	Use this setting when paper loaded cannot be used for 2-sided printing. Factory default settings: Disable
Disable Staple	Use this setting when paper used cannot be stapled. Factory default settings: Disable
Disable Punch	Use this setting when paper used cannot be punched. Factory default settings: Disable
Disable Fold	Use this setting when using paper that cannot be disable fold. Factory default settings: Disable

The settings that can be selected vary depending on the peripheral devices installed.

Paper Settings

Paper Tray Settings

Auto Switching of Tray

Display Paper Tray Settings when bypass tray detects paper.

Paper Weight Setting

Settings of each tray

Tray Settings

Tray Registration

Select Paper Sizes for Auto Detection

Custom Size Registration (Bypass)

Paper Settings

Side 1/2, XY Ratio/Print Position Auto Adjust

For automatic document feeder

For document glass

Side 1/2, XY Ratio Settings / Side 1/2, XY Print Position

Side 1/2, XY Ratio Settings

Side 1/2, XY Print Position Settings

Measurement patterns for Side 1/2, XY Ratio Settings / Side 1/2, XY Print Position Settings

Paper Type Registration

CONTENTS MENU