SHARP

Language

OUTPUT POSITION AND MARGIN ADJUSTMENT FUNCTIONS

ADDING MARGINS (MARGIN SHIFT)

This function shifts the copy image right, left or down to adjust the margin.
This is convenient when you wish to bind the copies with a string or in a binder.
Shifting the image to the right so the copies can be bound at the left edge

Not using the Margin Shift Using the Margin Shift

The punch holes cut off part of the image.

The image is moved to allow space for the holes so the image is not cut off.

Margin Shift

Margin Shift cannot be selected in easy mode.

Place the original.

Place the original in the document feeder tray of the automatic document feeder, or on the document glass.
AUTOMATIC DOCUMENT FEEDER
DOCUMENT GLASS

Tap the [Others] key, and tap the [Margin Shift] key.

Tap the image shift direction.

Sets a margin shift width.

Tap the numeric value display indicating the margin shift area on the front side or reverse side, and enter the area using the numeric keys.
After the settings are completed, tap [OK] and [Back] keys in sequence.
If you set the [Adjust 2nd pg value to 1st.] checkbox to , goes out and you can set sides 1 and 2 separately.
  • To cancel the margin shift setting:
  • Tap the [Off] key.
  • To cancel all settings:
  • Tap the [CA] key.

Tap the [Start] key to start copying.

ERASING PERIPHERAL SHADOWS FOR COPYING (ERASE)

The erase function is used to erase shadows around the edges of copies that occur when copying thick originals or books.
When a thick book is copied

Not using the Erase Using the Erase
Shadows appear on the copy

Shadows do not appear on the copy

Erase modes (Outer Frame Erase, Center Erase, Edge + Center Erase, Side Erase)

  • Erase cannot be selected in easy mode.
  • If a ratio setting is used in combination with an erase setting, the erase width will change according to the selected ratio. If the erase width setting is 1" (20 mm) and the image is reduced to 50%, the erase width will be 1/2" (10 mm).
  • This function erases the parts of the image where shadows tend to form, but does not detect shadows and erase only the shadows.
  • When Erase is selected, the orientation of the original is automatically set to portrait.

Place the original.

Place the original in the document feeder tray of the automatic document feeder, or on the document glass.
AUTOMATIC DOCUMENT FEEDER
DOCUMENT GLASS

Tap the [Others] key, and tap the [Erase] key.

Tap the checkbox of the edge that you wish to erase, and specify the erase position.

Check that the tapped checkbox is set to .
If the [Outer Frame] key is tapped, the [Up], [Down], [Left], and [Right] checkboxes are set to .
If the [Specify Frame+Center] key is tapped, all the checkboxes are set to .
Specify the erase edge on the reverse side when erasing edges of one to three sides of Up, Down, Left, and Right on the front side to scan a 2-sided original.
  • If the [Reverse erase position of back face] checkbox is set to , the edge in the position opposite to the erased edge on the front side will be erased.
  • If the [Reverse erase position of back face] checkbox is set to , the edge in the same position as on the front side will be erased.

Specify the erase width.

Tap the numeric value display indicating the erase width area on the front side or reverse side, and enter the area using the numeric keys.
After the settings are completed, tap [OK] and [Back] keys in sequence.
To quickly set the area, first specify a value close to the desired value by the numeric keys, then adjust it with .
  • To cancel the erase setting:
  • Tap the [Clear] key.
  • To cancel all settings:
  • Tap the [CA] key.

Tap the [Start] key to start copying.

COPYING IN THE CENTER OF THE PAPER (CENTERING)

This function centers the copied image on the paper.
This lets you place the image in the center of the paper when the original size is smaller than the paper size or when the image is reduced.

Not using the centering function Using the centering function
  • Centering cannot be selected in easy mode.
  • Centering must be specified before scanning the original.
  • When the original size or the paper size is displayed as a special size, this function cannot be used.
  • This function cannot be used in combination with an enlargement setting. If enlargement of 101% or more is selected, the enlargement is automatically returned to 100%.

Tap the [Others] key, and tap the [Centering] key.

A checkmark appears on the icon.
After the settings are completed, tap the [Back] key.
  • To cancel the centering setting:
  • Tap the [Centering] key to clear the checkmark.
  • To cancel all settings:
  • Tap the [CA] key.

Tap the [Start] key to start copying.

SPECIFYING A PAPER POSITION (POSITION IMAGE)

This function moves the scanned original to a specified position to make a copy.
You can make a copy in any desired position as you can fine adjust the position.
We recommend that you specify the top as the starting side of the original.

Position Image cannot be selected in easy mode.

Copy the original that you want to use for Move Copy.

Copying is performed without using move copy.

Measure the movement amount with the top as the starting side of the output copy.

Tap the [Others] key, and tap the [Position Image] key.

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Sets a movement distance.

Tap the area indicating the movement distance on the front or reverse side, and enter the distance using numeric keys.
After the settings are completed, tap [OK] and [Back] keys in sequence.
  • To quickly set the area, first specify a value close to the desired value by the numeric keys, then adjust it with .
  • If you set the [Adjust 2nd pg value to 1st.] checkbox to , goes out and you can set sides 1 and 2 separately.
  • If you want to copy in the horizontal orientation, specify "Left" as the starting side of the original.
  • Even if you copied in the horizontal orientation, setting the starting side of the original to the top enables measurement of the movement distance in the same way as in the vertical orientation.
To cancel the Position Image setting:
Tap the [Clear] key.

Place the original.

Place the original in the document feeder tray of the automatic document feeder, or on the document glass.
AUTOMATIC DOCUMENT FEEDER
DOCUMENT GLASS
To cancel all settings:
Tap the [CA] key.

Tap the [Start] key to start copying.

Language

Version 03a / bpb550wd_usr_03a _us

↑Top of page