SHARP

Language

REGULAR MAINTENANCE

To ensure that the machine continues to provide top quality performance, periodically clean the machine.

Warning

Do not use a flammable spray to clean the machine. If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine, fire or electrical shock may result.

Caution

  • Do not use thinner, benzene, or similar volatile cleaning agents to clean the machine. These may degrade or discolor the housing.
  • Use a soft cloth to gently wipe off dirt from the area on the operation panel with a mirror-like finish (shown at right). If you use a stiff cloth or rub hard, the surface may be damaged.

CLEANING THE DOCUMENT GLASS AND AUTOMATIC DOCUMENT FEEDER

If the document glass or document backplate sheet becomes dirty, the dirt will appear as dirty spots, colored lines, or white lines in the scanned image. Keep these parts clean at all times.
Wipe the parts with a clean, soft cloth.
If necessary, moisten the cloth with water or a small amount of neutral detergent. After that, wipe with a clean dry cloth.
Examples of lines in the image

Document glass

Document backplate sheet

SCANNING AREA

If black lines or white lines appear in images scanned using the automatic document feeder, clean the scanning area(the thin long glass next to the document glass).
To clean this part, use the glass cleaner that is stored in the automatic document feeder. After using the glass cleaner, be sure to return it to its storage position.

When using the BP-70C31 / BP-70C36 / BP-70C45 / BP-70C55 / BP-70C65

Open the automatic document feeder and remove the glass cleaner.

Clean the document scanning area on the document glass with the glass cleaner.

One scanning area is on the document glass and the other is inside the automatic document feeder.

Open the scanning area cover on the automatic document feeder.

Push in the release switch to release the cover.

Clean the scanning area in the automatic document feeder.

Close the cover.

Replace the glass cleaner.

When using the BP-50C26 /BP-50C31 / BP-50C36 / BP-50C45 / BP-50C55 / BP-50C65

Open the automatic document feeder and remove the glass cleaner.

Clean the document scanning area on the document glass with the glass cleaner.

Replace the glass cleaner.

CLEANING THE LASER UNIT

When the laser unit inside the machine becomes dirty, line patterns (colored lines) may form in the printed image.
Identifying lines (colored lines) caused by a dirty laser unit

  • Colored lines always appear in the same place. (The lines are never black.)
  • Colored lines appear in parallel with the direction of paper feeding.
  • Colored lines appear not only on output from a copier but also on prints from a computer. (The same lines appear on both copies and print jobs.)
If conditions similar to the above occur, clean the laser unit as explained below.

Open the front cover.

Open while pressing the convex parts on both sides.
When a finisher (large stacker) or saddle stitch finisher (large stacker) is installed on the BP-50C55/BP-50C65/BP-70C55/BP-70C65, open the front cover on the finisher (large stacker), or the front upper cover on the saddle stitch finisher (large stacker), before opening the front cover of the machine.

Remove the toner collection container.

Spread newspaper or something similar in advance where you will place the toner collection container.
Press the release buttons on the sides of the toner collection container, push the toner collection container down until the toner collection container stops, and then slowly lift it up to remove it.

Caution

  • Do not touch the internal cords or connectors.
  • The toner recovery container should be placed in an upright position, not collapsed.

Take out the cleaning tool for the laser unit.

The cleaning tool is attached to the front cover.
  1. Pull the right-hand side of the cleaning tool to detach it from the hook.
  2. Put it over the hook to place it on the back side.
  3. Turn the cleaning tool around the boss to detach it from the left hand hook.

Make sure that the cleaner at the tip of the cleaning tool is not dirty.

If the cleaner is dirty, remove the cleaner from the cleaning tool and replace it with a clean one.
For the procedure for replacing the cleaner, see steps 5 through 7. If the cleaner is not dirty, go to step 8.

Take out a replacement cleaner from the toner collection container.

Replacement cleaners are stored on the toner collection container. Grasp the end of the cleaner and pull it out of the toner collection container.
Remove the dirty cleaner from the tip of the cleaning tool.

Remove the dirty cleaner from the end of the cleaning tool.

  1. Firmly grasp the tool where the cleaner is attached.
  2. Use your other hand to press down on the hook that secures the cleaner, and remove the cleaner.

Caution

Put the removed cleaner back on the toner collection container.

Attach the new cleaner to the cleaning tool.

  1. Align the cleaner hook with the attachment hole in the cleaning tool.
  2. Hold the cleaner firmly and push the cleaning tool in.

Clean the laser unit.

  1. Point the cleaner down and slowly insert the tool into the hole that you wish to clean.
    2. Be sure to point the cleaner down.
    Labels similar to (A) are attached to areas that require cleaning.
  2. Insert the cleaning tool all the way into the hole and then pull it back out.
    3. Pull the cleaning tool out until you feel the tip of the tool leave the cleaning surface of the laser unit.
  3. Repeat step 2 two or three times and then remove the cleaning tool.

Caution

Do not touch the internal cords or connectors.

Repeat steps 8 to clean all holes (4 holes) in the laser unit.

The laser unit is cleaned in four locations, including the location cleaned in step 8. Clean all holes.

Replace the cleaning tool.

  1. Engage the cleaning tool onto the boss and turn it around it, and then put the edge (the cleaner side) on the left handhook.
  2. Put the right-hand side of the cleaning tool over the hook to place it on the near side.
  3. Turn the cleaning onto hook.

Push the toner collection container into the machine.

Push in until you hear a "click" sound indicating that the left and right locks are engaged.

Close the front cover.

Hold both sides and close.

CLEANING THE BYPASS FEED ROLLER

If paper misfeeds frequently occur when feeding envelopes or heavy paper through the bypass tray, wipe the surface of the feed roller with a clean soft cloth moistened with water or a neutral detergent.

CLEANING THE PAPER FEED ROLLER

When using the automatic document feeder, if the placed original is smudged or jammed, wipe the surface of the paper feed roller in the direction of the arrow with a clean, soft cloth moistened with water or a neutral detergent.
BP-50C26/BP-50C31/BP-50C36/BP-50C45/BP-50C55/BP-50C65

BP-70C31/BP-70C36/BP-70C45/BP-70C55/BP-70C65

CONTENTS MENU

Language

Version 04a / bp70c65_usr_04a_us

↑Top of page