LOADING PAPER IN THE TRAY 1/2
A maximum of 1200 sheets of 8-1/2" × 11" (A4) paper
can be loaded into tray 1.
A maximum of 800 sheets of 8-1/2" × 11" (A4) paper can be
loaded into tray 2.
If you loaded paper of a different type or size
from the paper previously loaded, be sure to check the settings
in "Settings (administrator)". An incorrect setting may cause
print failure, printing on paper of an incorrect size, or type or
paper misfeeds.
Caution
Do not place heavy objects on the tray or press
down on the tray.
To
check the type and size of paper:
[Tray Settings] in the home screen or in "Settings", select
[Status] → [Machine Identification] → [Paper Input Tray Status].
To set
the type and size of paper:
Set this in [Tray Settings] in the home screen or in "Settings",
select [System Settings] → [Common Settings] → [Paper Settings] → [Paper Tray Settings].
Pull out the paper tray.
Gently pull the tray out until it stops.
Keep holding the handle until the lock is released.
Fan the paper.
Fan the paper well before loading it. If the paper is
not fanned, multiple sheets may feed at once and cause a misfeed.
Lift the feed roller, and place paper into the tray.
- Load
the paper with the print side facing up. The stack must not be higher
than the indicator line (maximum of 1200 sheets for tray 1, or maximum
of 800 sheets for tray 2).
- Do not
load the paper as shown below.
Lower the feed roller, and gently push the paper tray
into the machine.
Push the tray firmly all the way into the machine slowly.
Forcefully inserting the paper may cause skewed feeding and
paper misfeeds.
CHANGING THE
PAPER SIZE
Remove the paper size guide.
With the base of the tray pressed all the way down, hold down
the hook at the bottom on the paper size guide and pull the paper
size guide up slightly.
Before changing the paper size of tray 2, raise
the paper guide.
Attach the paper size guide and transparent sheet appropriately
for the size of paper to be used.
- Align the bottom of the paper size guide with
the appropriate slot on the base of the tray.
Align the paper size guide with the slot for the paper size
to be used (indicated by the paper size mark).
- Align the holes at the top of the paper size guide with
the protrusions that secure the paper size guide.
Align with the holes for the paper size to be used (indicated
by the paper size mark).
- Push in the paper guide so that it locks into place.
Push the paper size guide in until the hook at the bottom
locks into place. (You will hear a "click" when the hook locks.)
Move the paper size guide slightly to verify that it has locked
into place.
- When attaching
the paper size guide, place the transparent sheet in direct contact
with the base of the tray in the correct orientation as shown.
- The slot
or hole with the "LT" mark is for 8-1/2" x 11" size.
Caution
When attaching the paper size guide, make sure
that the top and bottom of the guide are aligned to the same paper
size. If the top and bottom of the paper size guide are not aligned
to the same paper size, skewed feeding and misfeeds will result.
Repeat steps 1 and 2 to adjust the far paper guide to
the paper size to be used.
Be sure to adjust the far paper guide to the same size
as the near paper guide.
When removing and attaching the far paper size guide,
take care not to hit the front cover of the machine.
Adjusting only one paper guide may result in skewed
feeding or misfeeds.
Set the paper size and paper type.
Be sure to set the paper size and paper type by selecting
[Tray Settings] in the home screen or in "Settings", select [System Settings]
→ [Common Settings] → [Paper Settings] → [Paper Tray Settings].
If the paper size setting is not configured correctly,
automatic paper selection will not operate correctly and printing
may take place on the wrong size or type of paper or a misfeed may
occur.
