LOADING PAPER IN THE LARGE
CAPACITY TRAY
Use the large capacity tray for outputting massive prints
that cannot be processed using the regular tray.
Large capacity tray (MX-LC12) stores a maximum of 3500 sheets
of 8-1/2" × 11", A4 and B5 paper.
Large capacity tray (MX-LCX3 N) stores a maximum of 3000 sheets
of paper from 12" × 18" (A3W) to 8-1/2" × 11"R (B5).
When changing the paper size, consult the dealer or nearest SHARP
Service Department.
Caution
Do not place heavy objects on the tray or press
down on the tray.
To
check the type and size of paper:
[Tray Settings] in the home screen or
in "Settings", select [Status] → [Machine Identification] → [Paper Input Tray Status].
To set
the type and size of paper:
Set this in [Tray Settings] in the home screen or in "Settings",
select [System Settings] → [Common Settings] → [Paper Settings] → [Paper Tray Settings].
LARGE CAPACITY TRAY (MX-LC12)
Pull out the paper tray.
Gently pull the tray out until it stops.
Fan the paper.
Fan the paper well before loading it. If the paper is
not fanned, multiple sheets may feed at once and cause a misfeed.
Place the paper in the center of the paper table.
Load the paper with the print side facing down. The stack must
not be higher than the indicator line (maximum of 3500 sheets).
Gently push the paper tray into the machine.
Push the tray firmly all the way into the machine slowly.
Forcefully inserting the paper may cause skewed feeding and paper
misfeeds.
LARGE CAPACITY TRAY (MX-LCX3 N)
Press the operation button.
The operation button blinks, and the tray paper table
goes down to the paper loading position. Wait until the operation button
light goes off.
Do not pull out the tray until the light goes off.
If you pull out the tray forcibly while the button lights up or
blinks, a machine failure may be resulted.
Pull out the paper tray.
Gently pull the tray out until it stops.
Fan the paper.
Fan the paper well before loading it. If the paper is
not fanned, multiple sheets may feed at once and cause a misfeed.
Place the paper in the center of the paper table.
Load the paper with the print side facing down. The stack must
not be higher than the indicator line (maximum of 3000 sheets).
When a certain volume of paper is loaded, the paper table automatically
goes down slightly and stops. Repeat this operation in the same
way to load paper.
Caution
- Do
not insert your hand into the space inside the paper table when
you load paper.
- Do not
insert spare paper or objects into the space inside the tray.
Gently push the paper tray into the machine.
Push the tray firmly all the way into the machine slowly.
Forcefully inserting the paper may cause skewed feeding and
paper misfeeds.
The paper table goes up after the tray is pushed in.
The operation button blinks while the paper table goes up. The button
lights up when the paper table has gone up.
Changing the paper size for the large capacity tray (MX-LCX3
N)
Loosen the paper guide screw.
Slide the plate of the paper guide.
Slide the plate until the red line appears at the center
of the size window of the plate.
Adjust the paper guide to the paper size that will be
used.
Slide the paper guide forward or backward until the size mark
of the paper to be used (
or
) appears in the size window of the plate.
Secure the paper guide.
- Slide the plate of the paper guide.
Slide the plate until the paper size to be used appears in
the size window of the plate.
- Tighten the paper guide screw.
Repeat steps 1 through 4 to adjust the far paper guide
to the paper size to be used.
Be sure to adjust the far paper guide to the same paper
size as the near paper guide.
Caution
Adjusting only one paper guide may result in skewed
feeding or misfeeds.
Change the right paper guide to the paper size to be
used.
- While holding up the paper guide lock, slide the
paper guide to the paper size to be used.
- Release the paper guide lock.
- Move the paper guide slightly to the right and left so that
it locks into place.
You will hear a "click" when the paper guide locks.
Set the paper size and paper type.
Be sure to set the paper size and paper type by selecting
[Tray Settings] in the home screen or in "Settings", select [System Settings]
→ [Common Settings] → [Paper Settings] → [Paper Tray Settings].
If the paper size setting is not configured correctly,
automatic paper selection will not operate correctly and printing
may take place on the wrong size or type of paper or a misfeed may
occur.
_open.png)
_2.png)
_close.png)
BEFORE USING THE MACHINE
OPERATION OF THE MACHINE
COPIER
PRINTER
SCANNER
DOCUMENT FILING
MANUAL FINISHING
CONVENIENT USE OF THE MACHINE
SETTING MODE
TROUBLESHOOTING
APPENDIX
_open.png)
_2.png)
_4.png)
_changesize_04_01.png)
_changesize_04_02.png)
_close.png)
_changesize_01.png)
_changesize_02.png)
_changesize_03.png)
_changesize_04.png)
_changesize_05.png)
_changesize_06.png)
