LOADING PAPER IN THE LARGE CAPACITY TRAYS

Use the large capacity trays for outputting massive prints that cannot be processed using the regular tray. The large capacity trays store a maximum of 5000 sheets of paper (2500 sheets for tray 5 and 2500 sheets for tray 6) from 12" × 18" (A3W) to 7-1/4" × 10-1/2"R (B5R).

Other than plain paper, special media such as tab paper and transparency film can be loaded into the large capacity trays. To load tab paper, the dedicated guide must be installed.

Caution

Do not place heavy objects on the tray or press down on the tray.

To check the type and size of paper:
[Tray Settings] in the home screen or in "Settings", select [Status] → [Machine Identification] → [Paper Input Tray Status].
To set the type and size of paper:
Set this in [Tray Settings] in the home screen or in "Settings", select [System Settings] → [Common Settings] → [Paper Settings] → [Paper Tray Settings].

Press the operation button.

The operation button blinks, and the tray paper table goes down to the paper loading position. Wait until the operation button light goes off.

Caution

Do not pull out the tray until the light goes off. If you pull out the tray forcibly while the button lights up or blinks, a machine failure may be resulted.

Pull out the paper tray.

Gently pull the tray out until it stops.

Fan the paper.

Fan the paper well before loading it. If the paper is not fanned, multiple sheets may feed at once and cause a misfeed.

Load the paper.

Load the paper with the print side facing down. The stack must not be higher than the indicator line (maximum of 2500 sheets).

Gently push the paper tray into the machine.

Push the tray firmly all the way into the machine slowly.
Forcefully inserting the paper may cause skewed feeding and paper misfeeds.
The paper table goes up after the tray is pushed in.
The operation button blinks while the paper table goes up. The button lights up when the paper table has gone up.

LOADING THE TAB PAPER

Remove the tab paper guide.

The guide is stored in the upper tray.

Insert the tab paper into the tray.

Place the tab paper with the print side facing up so that the tab is to the right.

See the following figure and adjust the tab position of the tab paper.

Place the tab paper guide.

Place the guide on the top of the tab paper.

Gently push the tray into the machine, and set the paper type to tab paper.

Using "Paper Tray Settings" in the system settings, set the paper type to tab paper.

To set the paper type to tab paper:
Set this in [Tray Settings] in the home screen or in "Settings", select [System Settings] → [Common Settings] → [Paper Settings] → [Paper Tray Settings].

CHANGING THE PAPER SIZE

Loosen the paper guide screw.

Slide the plate of the paper guide.

Slide the plate until the red line appears at the center of the size window of the plate.
Both near and far plates slides when you slide one of those.

Adjust the paper guide to the paper size that will be used.

Slide the paper guide forward or backward until the size mark of the paper to be used (

) appears in the size window of the plate.
Both near and far plates slides when you slide one of those.

Secure the paper guide.

Slide the plate of the paper guide.

Tighten the paper guide screw.

Change the right paper guide to the paper size to be used.

While holding the paper guide lock, slide the paper guide to the paper size to be used.
Release the paper guide lock.
Move the paper guide slightly to the right and left so that it locks into place.

Set the paper size and paper type.

Be sure to set the paper size and paper type by selecting [Tray Settings] in the home screen or in "Settings", select [System Settings] → [Common Settings] → [Paper Settings] → [Paper Tray Settings].
If the paper size setting is not configured correctly, automatic paper selection will not operate correctly and printing may take place on the wrong size or type of paper or a misfeed may occur.

LOADING PAPER IN THE LARGE CAPACITY TRAYS

LOADING THE TAB PAPER

CHANGING THE PAPER SIZE

CONTENTS MENU