Digital multifunctional system BP-B537WR / BP-B547WD

This function shifts the copy image right, left or down to adjust the margin.
This is convenient when you wish to bind the copies with a string or in a binder.
Shifting the image to the right so the copies can be bound at the left edge

Not using the Margin Shift	Using the Margin Shift

The punch holes cut off part of the image.	The image is moved to allow space for the holes so the image is not cut off.

Margin Shift

‹-+›

Margin Shift cannot be selected in easy mode.

Place the original.

Place the original in the document feeder tray of the automatic document feeder, or on the document glass.
AUTOMATIC DOCUMENT FEEDER
DOCUMENT GLASS

Tap the [Others] key, and tap the [Margin Shift] key.

Tap the image shift direction.

Sets a margin shift width.

Tap the numeric value display indicating the margin shift area on the front side or reverse side, and enter the area using the numeric keys.
After the settings are completed, tap [OK] and [Back] keys in sequence.

If you set the [Adjust 2nd pg value to 1st.] checkbox to

,

goes out and you can set sides 1 and 2 separately.

To cancel the margin shift setting:

To cancel all settings:

Tap the [Start] key to start copying.

The erase function is used to erase shadows around the edges of copies that occur when copying thick originals or books.
When a thick book is copied

Not using the Erase	Using the Erase

Shadows appear on the copy	Shadows do not appear on the copy

Erase modes (Outer Frame Erase, Centre Erase, Edge + Centre Erase, Side Erase)

Erase cannot be selected in easy mode.
If a ratio setting is used in combination with an erase setting, the erase width will change according to the selected ratio. If the erase width setting is 20 mm (1") and the image is reduced to 50%, the erase width will be 10 mm (1/2").
This function erases the parts of the image where shadows tend to form, but does not detect shadows and erase only the shadows.
When Erase is selected, the orientation of the original is automatically set to portrait.

Place the original.

Place the original in the document feeder tray of the automatic document feeder, or on the document glass.
AUTOMATIC DOCUMENT FEEDER
DOCUMENT GLASS

Tap the [Others] key, and tap the [Erase] key.

Tap the checkbox of the edge that you wish to erase, and specify the erase position.

Check that the tapped checkbox is set to

.
If the [Outer Frame] key is tapped, the [Up], [Down], [Left], and [Right] checkboxes are set to

.
If the [Specify Frame+Centre] key is tapped, all the checkboxes are set to

.

Specify the erase edge on the reverse side when erasing edges of one to three sides of Up, Down, Left, and Right on the front side to scan a 2-sided original.

If the [Reverse erase position of back face] checkbox is set to , the edge in the position opposite to the erased edge on the front side will be erased.
If the [Reverse erase position of back face] checkbox is set to , the edge in the same position as on the front side will be erased.

Specify the erase width.

Tap the numeric value display indicating the erase width area on the front side or reverse side, and enter the area using the numeric keys.
After the settings are completed, tap [OK] and [Back] keys in sequence.

To quickly set the area, first specify a value close to the desired value by the numeric keys, then adjust it with

.

To cancel the erase setting:

To cancel all settings:

Tap the [Start] key to start copying.

This function centres the copied image on the paper.
This lets you place the image in the centre of the paper when the original size is smaller than the paper size or when the image is reduced.

Not using the centring function	Using the centring function

Centring cannot be selected in easy mode.
Centring must be specified before scanning the original.

When the original size or the paper size is displayed as a special size, this function cannot be used.
This function cannot be used in combination with an enlargement setting. If enlargement of 101% or more is selected, the enlargement is automatically returned to 100%.

Tap the [Others] key, and tap the [Centring] key.

A checkmark appears on the icon.
After the settings are completed, tap the [Back] key.

To cancel the centring setting:

To cancel all settings:

Tap the [Start] key to start copying.

This function moves the scanned original to a specified position to make a copy.
You can make a copy in any desired position as you can fine adjust the position.
We recommend that you specify the top as the starting side of the original.

‹-+›

Position Image cannot be selected in easy mode.

Copy the original that you want to use for Move Copy.

Copying is performed without using move copy.

Measure the movement amount with the top as the starting side of the output copy.

Tap the [Others] key, and tap the [Position Image] key.

Tap the [Original] key and specify the orientation of the original to have the orientation be correctly recognized.
SPECIFYING THE ORIENTATION OF THE ORIGINAL

Sets a movement distance.

Tap the area indicating the movement distance on the front or reverse side, and enter the distance using numeric keys.
After the settings are completed, tap [OK] and [Back] keys in sequence.

To quickly set the area, first specify a value close to the desired value by the numeric keys, then adjust it with .
If you set the [Adjust 2nd pg value to 1st.] checkbox to , goes out and you can set sides 1 and 2 separately.
If you want to copy in the horizontal orientation, specify "Left" as the starting side of the original.

To cancel the Position Image setting:
Tap the [Clear] key.

Place the original.

Place the original in the document feeder tray of the automatic document feeder, or on the document glass.
AUTOMATIC DOCUMENT FEEDER
DOCUMENT GLASS

To cancel all settings:
Tap the [CA] key.

Tap the [Start] key to start copying.

OUTPUT POSITION AND MARGIN ADJUSTMENT FUNCTIONS

ADDING MARGINS (MARGIN SHIFT)

ERASING PERIPHERAL SHADOWS FOR COPYING (ERASE)

COPYING IN THE CENTRE OF THE PAPER (CENTRING)

SPECIFYING A PAPER POSITION (POSITION IMAGE)

CONTENTS MENU